Here is an interesting email from the pyromagnetics guy, he read the
comments about the hot air and wrote the following;
-----------------------------
JERRY, your failing to grasp the fact that this machine IS and ALLWAYS
has been a WIND GENORATOR HYBRIDE...The air is allways flowing through
it, due to the natural pressure difference between the intake and its
exhaust holes...there must always be a slight updraft past the exhaust
holes to get things started PERIOD.
For those of your group that want a free Energy device NOW one less
complicated then my Imploders
1) Put a long permanent magnet (Cylindrical) into a plastic tube
longer then the magnet. The tubes I.D. must be such that the
magnet can slide FREELY inside the tube
2) Wrap insulated copper coil wire around the tube in the middle
the same length of the cylindrical magnet on the inside...all
you have made is a permanent magnet solenoid.
3) NOW ATTACH A COIL SPRING OR ELASTIC BAND TO THE INTERNAL
CYLINDRICAL MAGNET SO IT IS FREE TO BOUNCE INSIDE THE TUBE
THE OTHER TWO ENDS OF THE SPRING NATURALLY ATTACH TO THE ENDS OF THE
TUBE. FREELY SUSPENDING THE MAGNET AT THE MIDDLE OF THE TUBE.
ANY OSCILLATION OF THE TUBE AND CONSEQUENTLY THE CYLINDRICAL MAGNET
GENERATES A.C. CURRENT... AS THE MAGNET FREELY BOUNCES UP AND DOWN
INSIDE THE TUBE.
NOW THAT YOU HAVE THAT, YOU CAN CONNECT A RECTIFIER TO THE COIL AROUND
THE BOUNCING MAGNET TUBE AND STORE CURRENT IN A CAPACITOR BANK....THE
TRICK IS TO THEN ADJUST THE SPRINGS OR ELASTOMERS SO THAT THE MAGNET IS
CLOSER TO THE BOTTOM OF THE TUBE WHEN THE TUBE IS HELD VERTICALLY
AGAINST GRAVITY.
BY FEEDING BACK THE STORED CURRENT BY BRIEFLY SHUNTING THE RECTIFIER THE
MAGNET WILL BOUNCE. BE CERTAIN THE D.C. PULSE OF THE TUBES COIL RECIEVED
FROM THE CAPACITOR BANK IS POLORIZED SO THE MAGNET IS "PULLED" INTO THE
MIDDLE OF THE SOLENOID.
THE MAGNET NOW BOUNCES AND THE RECTIFIER RECONNECTS AUTOMATICALLY SINCE
THE SHUNT SWITCH WAS ONLY PULSED.
IF YOUR OUTSIDE WITH A PARACHUTE HARNESSED CONICAL HAT, (to focus the
rising heat from your body, estimated at 300 watts), THE LARGER OR
HEAVIER YOU ARE......THE JUMPING SOLENOID STICK WILL CONTINOUSLY
REGENERATE ITS ENERGY SUPPLY...DUE TO THE CONVERSION OF NATURAL
OSCILLATION INTO FREE ELECTRIC POWER.
THE SHUNT SWITCH IS AT THE BASE OF THE JUMPING TUBE AND PUSHED AGAINST
THE GROUND WHEN PULSED...THE ENTIRE POINT IS TO KEEP THAT MAGNET
BOUNCING INSIDE THAT TUBE AND THEN BRIEFLY JUMP INTO THE AIR.
THE CONICAL HAT RIGID PARACHUTE HARNASSED TO YOUR BODY PROVIDES ALL THE
OSCILLATION REQUIRED TO RECHARGE THE CAPACITOR BANK.....PLEASE CONSIDER
IT.
I DESIGNED IT MORE AS AN AMUSEMENT THEN AN F.E. DEVICE BUT IT WILL
WORK ...IT MAY ALSO BE POSSIBLE TO BUILD AN INDOOR VERSION THAT JUMPS
OFF THE TABLE LIKE A TOY, THEN FLOATS BACK DOWN WITH A SMALL RIGID
CONICAL PARACHUTE ATTACHED TO THE BOUNCING MAGNET TUBE AND THE CAPACITOR
BANK OFF TO THE SIDE CONNECTED TO THE TOY BY PIG TAIL WIRES SO AS NOT TO
INTERFERE WITH THE TOYS BOUNCE...TRY IT.
IT WORKS UNLESS THE LAWS OF PHYSICS ARE SOME HOW DIFFERENT IN YOUR PART
OF THE WORLD THEN MINE...
----------------------------
Interesting, a magnet, attached to a spring, moving up and down to
induce current flow in the coil to charge a capacitor. An optical
switch could be hooked in so that when the magnet blocked the beam for
longer than a given time, the capacitor would discharge into a coil that
would throw the magnet back into oscillation. Just like EV Gray's high
voltage solenoid to drive his motor...hmm....this could damn sure work!!
-- Jerry W. Decker / jdecker@keelynet.com http://keelynet.com / "From an Art to a Science" Voice : (214) 324-8741 / FAX : (214) 324-3501 KeelyNet - PO BOX 870716 - Mesquite - Republic of Texas - 75187