The following are the details as removed from the file TESLAFE1 :
"The standard internal combustion engine was removed and an 80-H.P. 1800 r.p.m electric motor installed to the clutch and transmission. The A.C. motor measured 40 inches long and 30 inches in diameter and the power leads were left standing in the air - no external power source! He then went to a local radio store and purchased a handful of tubes (12), wires and assorted resistors. A box measuring 24 inches long, 12 inches wide and 6 inches high was assembled housing the circuit. The box was placed on the front seat and had its wires connected to the air-cooled, brushless motor. Two rods 1/4" in diameter stuck out of the box about 3" in length."The mention of this experiment in a local paper kind of blew me away but it did give "some" detail of what was in this mysterious power box. We know that T.H. Moray had probably the best known version of such a device. In his case he used a special "valve" which appeared to be basically a diode. Except this diode worked more like a Triac. That is, any electrical wave, both positive AND negative going currents, was picked up by an antenna and passed through this diode with minimal loss of energy. As far as we know, this valve was based on a composite substance with GERMANIUM as the host material. From there it went through a tuned circuit based on vacuum tubes and capacitors to build and discharge the energy as demanded by the load. The tuned circuits were resonant with one or more earth or cosmic frequencies and the vacuum tubes acted as harmonic constructive interference amplifiers of the input signals. We will note that Moray's resonant circuits used CAPACITORS, COILS and RESISTORS. Experiments done during Moray's heyday showed an output up to 50,000 Watts of high frequency energy. It is believed that the energy was high frequency because 100 watt light bulbs burned cool to the touch. One other CRITICAL POINT about Moray's converter was that it would ONLY energize RESISTIVE loads and NOT INDUCTIVE loads. This is because inductive loads imply coils of wire which are heated more so by HYSTERESIS (interferring electro-magnetic fields) rather than simple resistance from the flow of current through molecular/atomic patterns. This type of interferring field caused an energy backup and subsequent de-tuning of Moray's generator. Since it was essentially a TUNED device, it could not compensate for any frequency changes or distortions ONCE TUNED. As a result, any attempt to hook up an inductive load would cause the device to stop generating electrical energy. To restart it, all inductive loading must be removed, the device re-tuned and restarted. Moray also used an unusual mode of operation for a vacuum tube in that he operated with a "cold cathode." This did not require a heated plate for the "thermionic emissions" deemed necessary to successful vacuum tube operation. There is also mention of radioactive elements in the antenna circuit which leads one to think he might have been tuning into the continual radioactive decay processes of nature, rather than cosmic or earth energies. Now to the Tesla Power Box We will first of all note the use of an AC coil motor. This alone tells us that the Tesla device was superior and not so dependent on tuning as was Moray's machine which could only power RESISTIVE loads. All universal energy moves in WAVES and so is essentially for alternating current (AC). That is why Moray called his book "THE SEA OF ENERGY IN WHICH THE EARTH FLOATS". The entire universe is continually bathed in these AC energies and they cover the entire frequency spectrum. What intrigues the hell out of me was how Tesla could use "off-the- shelf" vacuum tubes and other components, put them together in the correct configuration and make it work. Another point we should note is the list of components :
- 1) 12 Vacuum Tubes (70L7-GT rectifier beam power tubes)
- 2) Wires
- 3) Assorted Resistors
- 4) 1/4" diameter rods 3" in length
- 1) Resistors AND capacitors
- 2) Capacitors AND coils
- 3) Coils AND resistors
(I cannot express Lambda here so we will use w for wavelength)
w = wavelength
v = velocity of propagation
f = signal frequency
a short example : w = v / f = wavelength in feet
w = 984,000,000/1,500,000 = 656 feet
f = 984,000,000/656 = 1,500,000 or 1.5 MHZ
3 inches * 4 = 1 foot
984,000,000/1 = 984,000,000
984,000,000/4 = 246,000,000 or 246 MHZ
Vacuum Tube Transistor Polarity
Operates from Voltage Current
lower plate emitter negative - cathode
grid base neutral
upper plate collector positive - anode
In the case of the Tesla Power Box, the vacuum tube appears to function
as a "pump", collecting incoming current in the form of ion intensification.
Once this "compressed" ion field reaches a certain density, the pump allows it
to be released into the next stage of the circuit, be it the actual load or
another vacuum tube.
So if the circuit is 6 vacuum tubes in parallel, all fed from a common
antenna, outputting to a common load terminal, then the common antenna
input would feed all vacuum tubes with the same wave. This would give the
greatest CURRENT accumulation because of the EXPANDED SURFACE AREA of the
paralleled tubes.
Note, these vacuum tubes most likely operate in the "cold cathode" mode
since the heaters of the vacuum tubes were not fed by any outside
voltage to provide the heat for the more orthodox therionic emission.
If the vacuum tubes are hooked in series, then one "pump" would feed another
"pump" to get successively higher densities of electrons. This would give
higher VOLTAGES because of increased PRESSURE.
Keep in mind that electricity is much like air or water. We can think of
voltage as pounds per square inch (PSI) and current as cubic feet per
minute (CFM). That is PSI is pressure, CFM is flow.
Another analog is comparing a river to electricity. In such a
comparison, the speed of the river is the VOLTAGE or pressure while the width
of the river is the CURRENT or rate of flow.
Such a comparison shows WHY current requires THE GREATEST SURFACE AREA for
the maximum flow. Fuses function on just this principle, when the current
flows over the surface of the fuse, it creates heat. If too much
current flows, it creates too much heat causing the fuse to melt and separate.
The more surface area the fuse, the greater the amount of current can flow,
another reason to not place a penny in a fuse socket.
So we have two antennas (1/4" diameter, 3" long rods), two sets of 6 vacuum
tubes connected together by wire and assorted resistors. As the waves of
energy are collected by the 3" rods, positive on one, negative on another,
the energy builds up in the form of increased ions in each of the
paralleled vacuum tubes. As in Moray's generator, the circuit will feed
whatever load is attached as long as it does not EXCEED the current carrying
capacity of the circuit components. What we have is an energy pumping
system.
I made a drawing of the box with some idea of the circuit. My
electronics knowledge is on IC's and transistors with almost nothing in regard
to vacuum tubes so there won't be much technical concept of the circuit per
se. Perhaps after some study, either I or someone else will come up with
some testable or useable circuits. 
The Parallel Version
The Serial Version